Expert Plumbing Services Built For Reliability
- Reliable Workmanship
- Clear Communication
- Homes, Townhomes & Condos
- Safety-Focused Service
- Emergency Plumbing Support
LOCAL PLUMBING EXPERTS
Trusted Plumbing Solutions for Homes and Businesses in Wylie
Available day & night, Monday to Sunday
Wylie Pipe Pros provides reliable plumbing repairs and installations for homes and businesses throughout Wylie, TX. From drain cleaning and water heater service to pipe repairs, fixtures, garbage disposals, and emergency plumbing, we focus on dependable workmanship and long-term solutions.
Plumber in Wylie, TX for water lines and slabs
When a house in Wylie loses pressure or the yard stays wet, a plumber in Wylie, TX starts at the buried run from the Collin County meter to the house. Wylie Pipe Pros helps homeowners, townhomes, and condos in Wylie, Lavon, Nevada, Josephine, and Caddo Mills with that meter-to-house line, slab leaks, pipe repair, drain cleaning, hot water heater work, fixture installation, and garbage disposal repair. We treat drains and heaters as the equipment those lines feed, and we take those calls 24/7.
Most of the streets we work sit in 75098, where the 2000s boom put copper and PEX on slab, and a smaller older core near Ballard still carries galvanized. Hard city water scales the heater at the end of that run. Clay under the slab does the rest.
We read pressure at the meter and at a hose bib before we open a wall or a trench, and we leave the rooms the way we found them. Those two gauges tell us whether a section repair will hold or the line has to come out. The visit that follows is the same sequence every time, from the first message to the last pressure check.
Reliable plumbing solutions for homes and businesses throughout Wylie, TX.
Professional repairs and installations completed with care, attention, and lasting results.
Need urgent plumbing help? Call Wylie Pipe Pros for fast assistance with leaks, burst pipes, backups, and other plumbing emergencies.
How a visit runs from the first call
You send the address and what the house is doing
Tell us the ZIP, the decade of the house if you know it, whether the wet spot is on slab or in a yard, and whether the house valve is already off. A photo of the meter or the stain is enough to decide which gauges come off the truck. We work in houses, townhomes, condos, and businesses, so the questions stay on your fixtures and your buried line. That note is how we show up with the right camera, the right pipe, and the right isolation fittings.
We set the window and roll with test gear
Once we have the street and the symptom, we put you on the board for the next open window, including nights and weekends. The truck carries a gauge set, an acoustic pickup, a thermal camera, and common copper, PEX, and PVC repair parts. Kristen Court is our shop street, so a 75098 address is a short hop, and the same kit goes east toward Lavon. Same-day diagnosis means those tests happen on the first visit, not on a return trip after a guess.
We measure before we cut
Static pressure at the meter is the baseline. Pressure at a hose bib on the house side shows what the buried run is doing. If the meter still turns with every fixture shut, water is leaving the system, and we listen along the slab edge and the yard path. Those readings rule out a city-main issue, a single failing faucet, and a heater that is only scaling. We talk through the numbers in the driveway so the next step is a choice, not a surprise.
We repair and we check the house again
After the repair, we restore pressure slowly and watch the meter, the joints, and the slab for a full cycle. Fixtures get a hot and cold check so a closed valve did not hide a second leak. Dirt goes back in the trench, and interior rooms get wiped down. If the job was a water line, we leave you with the shutoff location and the material we put in the ground. That last pass is how we know the house will hold overnight.
Water lines, leaks, and the rest of the house
Water line replacement on the meter-to-house run
The buried run is the pipe that fails first on Houston Black clay because it cannot flex when the yard heaves. A homeowner notices it as a wet stripe, a meter that never sits still, or pressure that dies at every tap. That is daily life, not a curiosity, because the whole house drinks from that one line. We treat the run as the job, not as a side note to a faucet.
Signs it is time to call
- The meter turns after every indoor fixture is off.
- A soft or bright green strip sits between the meter and the slab.
- Pressure is weak at every tap, not just one bath.
- You hear water in the yard when the house is quiet.
- The water bill jumped with no change in habits.
- Hot and cold both fade at the same time.
We isolate the house, compare meter pressure to hose-bib pressure, and probe the bury path before we trench. If a short span is sound copper or PEX, a section coupling can hold. If the wall is thin or the material is from an era that does not last in this clay, we pull the full run and bed new pipe. Water line replacement is the page for that choice. Main water line leak repair on these lots is a yard problem long before it is a kitchen problem.
Leak detection on slab and in the yard
A stain on the floor or a hiss at the slab edge is how a leak announces itself in this housing. Waiting turns a small wet spot into lifted plank and a clay pocket that will not dry. We would rather map the path with sound and temperature than open three rooms to find one pin hole.
What you might notice first
- A warm stripe on the floor when the heater is on.
- The sound of water with every tap closed.
- Rust colored water from the taps after a quiet night.
- A ceiling stain under an upstairs bath.
- The HVAC closet or hall slab that never dries.
- A hiss inside a wall after the pump cycles.
Acoustic listening at the slab edge, a thermal pass, and a meter watch tell us whether the leak is in the buried run, under the slab, or in a wall. That order is how we fix a leaking pipe in a wall without turning the hall into a chase. Leak detection is the visit that owns those instruments. A plumber for a leaking ceiling still starts with those same readings.
Pipe repair, slab leaks, and repiping
Inside the house, copper from the 1990s pits, galvanized in the older core rusts shut, and a slab leak on clay will follow the same crack the foundation already made. A section repair is the right call when the rest of the pipe still holds. A repipe is the right call when every joint is a future leak.
How this shows up in the house
- Pinholes that return a few feet from the last patch.
- Banging pipes in the walls when a valve shuts.
- Low flow at the far bath only.
- Green crust on copper under a sink.
- A wet band along a baseboard on slab.
- A shutoff that will not turn without crumbling.
We cut a sample, pressure-test the remaining span, and only then choose a coupling, a reroute, or a full repipe. Pipe repair is the page that walks that decision. Burst pipe repair after a freeze uses the same test, because a split that looks small can open again at the next cold night.
Emergency plumbing when water will not stop
A burst line at 2 a.m. is the same physics as a slow yard leak, only faster. Knowing how to stop an emergency water leak starts at the meter valve, not at a towel. We take those calls around the clock because a slab that floods overnight feeds the clay and the flooring at the same time.
Clues in the yard and house
- Water spraying from a hose bib or yard box.
- A ceiling that sags while a tap is open.
- No water at all after a bang in the wall.
- A hot water heater leaking from the bottom onto the slab.
- Sewage backing into a tub while the house is in use.
- A meter that spins hard with every fixture off.
We shut the house, relieve pressure, and find the split before we talk about pipe. An emergency plumber for a burst pipe on these streets is a gauge set and a valve key, not a lecture. Emergency plumbing covers that first hour. A 24 hour plumber still runs the same meter-to-bib test once the spray is stopped.
Hot water heaters at the end of the line
The heater is the last piece of the water line, and hard city water is what kills it. Scale on the lower element makes the tank run long, then sediment holds heat against the steel until the bottom weeps. That is why a 2000s Wylie house often needs heater work before it needs a kitchen remodel.
What the house is telling you
- Hot water that fades after a short shower.
- Popping in the tank while it fires.
- Water around the pan or the drain.
- A T&P valve, which relieves pressure on the tank, that weeps.
- Rusty hot water with clear cold water.
- A tank that is cold at the top after a long recovery.
We read inlet temperature, element resistance, and T&P discharge before we flush or pull the tank. Water heater repair the same day is a first-visit test of those parts. When the tank wall is thin, we replace an old water heater with the same connections the buried run already feeds. Water heater repair and tankless water heater work both start there.
Drain cleaning on kitchen and bath lines
A clogged kitchen sink or a slow draining bathtub is the house telling you the lateral is coating or belly-bound. Grease and soap do that on PVC the same way roots did it on older clay. Snaking without looking is how the same sink backs up a week later.
What homeowners report
- A kitchen sink drain that keeps backing up after dinner.
- A tub that falls slowly even after a chemical pour.
- Who to call for a clogged toilet that repeats on the same bath.
- Gurgling at a sink when the washer drains.
- An upstairs shower that leaves the tub below wet.
- A floor drain that smells after a rain.
We cable, then camera, so a belly or a broken hub is on the screen before we cut. Drain cleaning for a clogged kitchen sink is a line problem, not a strainer problem, when it returns. Drain cleaning is that camera-and-cable visit. Clogged drain repair on a shared stack needs both floors running water while we watch.
Fixture installation and the valves behind them
A faucet dripping all night or a shower that will not stay mixed is often the cartridge, but on older Wylie copper it can be the valve body in the wall. Replacing the trim without reading the stop is how a small drip becomes a wet hall. We treat the fixture as the end of the same water line we just tested.
Early warnings at the fixture
- A faucet dripping all night at the kitchen.
- A shower that scalds when a toilet fills.
- A toilet that ghost-fills every hour.
- A supply stop that crumbles when turned.
- Uneven flow between hot and cold on one tap.
- A new vanity that still weeps at the angle stop.
We shut the stops, pull the cartridge, and inspect the valve body before a shower valve replacement. Fixture installation includes the stops, not just the chrome. Toilet repair and faucet repair on a condo or townhome follow the same isolation so a shared wall does not take the water.
Garbage disposal repair under the kitchen sink
A garbage disposal jammed on a bone or a failed reset is a kitchen stop, but a hum with no turn can also mean a seized bearing or a loose knock in the drain. We do not run the unit against a clogged trap. The disposal is another piece of equipment the water line and the drain both serve.
Sounds and stains to watch
- A unit that hums and will not spin.
- Water at the dishwasher hose after a cycle.
- A reset button that will not stay in.
- Black film under the splash guard.
- A knock that continues after the switch is off.
- A leak at the flange onto the cabinet floor.
We kill power, check the flywheel, and only then talk about a replacement. Garbage disposal repair is that under-sink visit. If the trap is the real stop, we move to the drain line instead of swapping a motor that was never the fault.
Gas line work at ranges, dryers, and logs
Appliance connectors fail at the nut and at the shutoff, especially where a range was slid a hundred times. We soap joints and confirm the connector type before the appliance goes back. If you smell gas or suspect a gas leak, go outside immediately and call 911. This is a serious emergency that needs urgent attention from the gas company.
Yard and floor clues
- A hiss at the range shutoff when the knob is off.
- A dryer that will not hold a flame.
- A connector that is kinked behind the stove.
- A shutoff that will not turn by hand.
- A log set that pops at the valve.
- A smell only when the range is pulled out.
We cap, test, and replace the connector and the valve if either fails. Gas line repair at the appliance is that work. It is never a substitute for the utility on a yard main or a smell in the street. Full service plumbing on this crew still stops at the appliance valve, not the street tap.
What We Offer
Quality Plumbing Solutions Designed For Performance
Plumbing emergencies can cause serious damage when left untreated. Get fast help for burst pipes, major leaks, sewer backups, overflowing fixtures, and other urgent plumbing problems.
Hidden plumbing leaks can cause water damage, higher utility bills, and moisture problems. We locate concealed leaks quickly so the source can be repaired before further damage occurs.
Leaking, damaged, or aging pipes can lead to water damage, low pressure, and costly repairs. We identify the problem and provide reliable pipe repair solutions designed to restore proper flow.
Slow or clogged drains can quickly become a bigger plumbing problem. We clear stubborn blockages and restore proper drainage for sinks, showers, toilets, and main drain lines.
Reliable hot water is essential for everyday comfort. We repair and service water heaters experiencing leaks, inconsistent temperatures, unusual noises, or a complete loss of hot water.
A jammed, leaking, or noisy garbage disposal can disrupt your kitchen routine. We diagnose disposal problems and provide repair or replacement solutions to restore proper operation.
Keep your plumbing system running smoothly with professional repairs, installations, and maintenance. From everyday issues to larger plumbing concerns, we provide dependable solutions for homes and businesses.
Upgrade or replace faucets, sinks, toilets, and other plumbing fixtures with professional installation. Proper connections help prevent leaks and ensure reliable performance.
Why Wylie homeowners call this crew
The shop sits on Kristen Court in 75098
The truck leaves from 101 Kristen Ct, so a call on the west side of town is not a long empty drive. Parts for copper, PEX, and PVC ride with us because those are the three materials the 2000s boom and the older core both use. That is a location fact, not a slogan. It is also why a local plumber can be in a Woodbridge or Ballard house without waiting on a warehouse run.
We test before we cut drywall or clay
Two gauges and a listening pickup cost less time than a wrong trench. We will not open a hall to chase a stain that the meter already placed in the yard. That habit is how we keep a plumbing inspection honest. The about page is where we spell out that four-beat order in more detail.
We leave the house the way we found it
Trench spoil goes back, interior rooms get wiped, and shutoffs return to the position you use. A best plumber for older homes still has to respect plaster and original trim on Ballard. Newer slab houses get the same courtesy on the flooring. The last pressure check is done with you in the kitchen, not from the truck.
We take the call at any hour
A slab leak does not wait for weekday daylight, and neither does a heater that floods a closet. Dispatch is 24/7, and the same test order applies at night. If you want a longer list of how we handle odd hours, the plumbing questions page collects them. A same day plumber on this crew is still that first-visit set of readings.
What Collin County soil and city water do to Wylie plumbing
Houston Black clay and the buried run
Houston Black clay is a Vertisol, which means it swells when it wets and cracks when it dries. That motion is strongest in the top few feet, exactly where the meter-to-house pipe lives. A coupling that was tight in April can be in shear by August. We see that as a wet stripe, a meter that never rests, and a slab edge that stays cool. The soil does not care whether the pipe is copper or PEX; it loads the fittings either way. Summer irrigation soaks the same clay and adds a second cycle of swell on top of the seasonal rain.
Hard city water at the heater and the valves
City of Wylie water is purchased surface water from Lavon Lake and the NTMWD plants, and it lands in the hard range, about eight to nine grains. Scale plates elements, clogs heater dip tubes, and leaves crust on shower valves. A homeowner feels it as fading hot water and as a faucet that will not shut crisp. We descale when the tank wall is still sound, and we pull the tank when the bottom is already weeping. City of Wylie is named here as the seller; after that we just say city water or Collin County tap water.
Winter freeze on attic and exterior-wall pipe
North Texas houses were not framed for a long freeze. Pipes in attics and in exterior walls split when the heat is out and the wind is on the brick. We thaw with controlled heat, then pressure-test, because the split often hides until the ice melts. Hose bibs and heater drains are the next failures on that same night. Frozen pipe repair in winter on this housing is a material and insulation problem, not a mystery. The clay is quieter in the cold; the freeze is what opens the pipe.
Summer demand and winter freeze on local pipes
Summer irrigation and the meter run
NTMWD production nearly doubles in summer, and Wylie watering rules run from April through October because demand hits the mains. That extra volume loads every weak joint on the buried run. A leak that wept in January becomes a river when the sprinkler clock is on. We find those leaks the same way we find winter leaks: meter, hose bib, then the yard path. State Highway 78 carries a lot of that summer traffic toward the lake side of town, and the yards along it show the same wet-meter pattern.
Winter freeze after the heat drops
When a hard freeze sits on the county, uninsulated hose bibs and attic runs are the first to split. We still start at the house valve, then we test. A burst in an exterior wall can look like a slab leak until the gauges place it. FM 544 on the south side of town has the same housing mix, so the same freeze pattern shows up there. After the repair we look at the heater drain and the other bibs, because one split rarely travels alone.
Houses we know in Wylie and nearby towns
Wylie sits primarily in Collin County, with edges in Dallas and Rockwall counties, and the housing tells you the pipe. Downtown is the older stock. The 2000s streets are copper and PEX on slab. We work those streets as a residential plumber, and the plumbing services hub lists every line of work in one place.
Historic downtown on Ballard Avenue
The Downtown Historic District around Ballard and Olde City Park still holds cottages and storefronts from before the boom. Galvanized and copper are the usual metals, and galvanized is what rusts shut and throws rust colored water from the taps. A leak there is often in a wall, not in a 200-foot bury.
Woodbridge on Springwell Parkway
Woodbridge went in during the 2000s with community pipe in copper, PVC, and PEX on slab. The clay still moves, so the meter run and the slab are the failures we see, not 1950s galvanized. Woodbridge Park at 230 Springwell is the anchor most residents name.
Kreymer Estates on Lyndhurst Drive
Kreymer Estates is newer, so PEX and PVC dominate, and the leaks we see are fittings and bury nicks more than rust. Kreymer Estates Park and Kreymer Lane mark the pocket. Low water pressure here is often a regulator or a heater, not a 40-year-old main.
Birmingham Farms on Odenville Drive
Birmingham Farms sits on a 1990s-to-2000s mix, copper and PVC, with Birmingham Farms Park at 725 Odenville as the landmark. Copper pinhole leaks and slab edge stains are the usual calls. The soil is the same Houston Black, so the bury path still shears at the fittings.
Bozman Farm Estates on Valley Stream Drive
Bozman Park at 1330 Valley Stream anchors a newer pocket where PEX is the default. Yard leaks still happen when the trench was backfilled tight in clay. We pressure-test before we blame the material.
Lavon on SH 78
Lavon is Collin County, but Bear Creek Special Utility District sells the water. The housing is mostly new slab along SH 78 and SH 205. Plumbing in Lavon is its own page because the seller and the pipe era are not Wylie’s downtown mix.
Nevada on FM 6
Nevada is Collin County with Nevada Special Utility District on the tap. Older rural houses on FM 1138 sit next to newer streets, so we confirm material at the meter before we cut. Plumbing in Nevada covers that mix.
Josephine on the Collin and Hunt edge
Josephine straddles Collin and Hunt counties, and the City of Josephine sells the water. The boom streets are very new PEX on slab, and a yard leak there is usually a fitting or a scrape, not galvanized. Plumbing in Josephine is written for that boom, not for Ballard Avenue.
Caddo Mills in Hunt County
Caddo Mills is Hunt County, not Collin, and the City of Caddo Mills bills most in-town homes. Main Street still has older stock; FM 36 and SH 66 have the new slabs. Plumbing in Caddo Mills states that county difference on every visit.
Why a buried water line is a poor DIY job
A buried water line shares the trench with electrical conduit on some lots, and a shovel does not know the difference. Cutting a live cable in wet clay is how a leak becomes an electrocution risk. We locate, we isolate, and we only open what the gauges already named.
Appliance gas sits in the same utility corridor on many slabs. A cut that nicks a fuel line is not a water repair anymore. Water damage from a missed clamp will lift flooring and feed Houston Black clay until the slab moves. Fragile PEX rings and copper sweat joints fail when they are reused with the wrong tool, and a homeowner cannot see that failure until the trench is already closed.
Misdiagnosis is the expensive part. A wet hall can be a slab leak, a heater pan, or a shower valve, and they do not share a repair. Modern pressure regulators and tankless boards do not survive a wet short. If you need a plumber for a condo or townhome, a wrong shutoff can take water from a neighbor. Leave the trench, the fuel, and the panel to a crew that will test first.
Questions about water lines and slab leaks
Why does the buried run from the meter fail on Collin clay?
Houston Black clay swells when it takes on rain and shrinks when it dries, and that motion is strongest right under the yard. The service line from the meter to the slab has no room to flex the way a copper branch inside a wall does, so joints fatigue and the pipe wall can crease. We compare static pressure at the meter with pressure at a hose bib, then listen on the buried path. If the drop is only on the house side of the meter, the run itself is the failure, not the city main.
Can a short section of water line be saved or does the whole run come out?
A clean break on otherwise sound copper or PEX can take a coupling if the rest of the run holds pressure and the soil has not chewed the wall thin. When we see pinholes in a row, green staining along several fittings, or a polybutylene stamp from the late 1980s, a short patch only moves the next leak a few feet. We pressure-test the remaining pipe and inspect a cut sample before we call a section repair good. If the wall is thin or the material is past its era, pulling the full meter-to-house line is the repair that lasts.
What does low water pressure at every tap usually mean here?
When every fixture is weak, the restriction is almost never a single faucet washer. Hard Collin County tap water leaves scale in the heater and in the main valves, and a crushed or leaking buried run will steal volume before water ever reaches the manifold. We read the meter, then the hose bib, then a bathroom tap so the numbers show which span is starving the house. That sequence is how a plumber to fix low water pressure decides between a clogged heater dip tube, a failing pressure regulator, and a yard leak.
Who can I call for a plumber near me in Wylie when the slab is wet?
A wet slab is a water-line problem until the tests say otherwise. We isolate the house, watch the meter, and use acoustic listening at the slab edge so we are not cutting tile to chase a stain. If the leak is in the buried run, we repair from the yard. If it is under the slab, we map it and talk through a section repair versus a reroute. That work is available 24/7 because a slab that stays wet will lift finish flooring and feed the clay under the house.
How do you find a slab leak without opening every room?
We start with a meter that still turns after every fixture is shut. That proves water is leaving the system. Acoustic listening along the slab edge and at hose bibs usually narrows the zone to one room or one yard run. A thermal scan of the floor can show a warm stripe where hot supply is escaping. Only after those readings agree do we open a small inspection point. That order keeps a slab leak repair from turning into a row of holes that miss the pipe.
Why does hard city water wear out a hot water heater?
Scale from hard city water plates the lower element and the tank bottom, so the heater works longer to make the same hot water. Sediment also holds heat against the steel, which thins the tank and shows up as a water heater leaking from the bottom. We check inlet temperature, T&P discharge, and element resistance before we talk about a flush versus a replacement. On a 2000s Wylie slab home the heater is often the first appliance the buried run feeds, so a failing tank can also flag a pressure or scale problem upstream.
Questions about heaters, drains, and towns
What should a Wylie homeowner do when a pipe freezes?
Shut the house valve at the meter if you can reach it, and leave faucets closed so a thaw does not spray an interior wall. Do not torch a frozen pipe. We thaw with controlled heat, then pressure-test the span because a split often opens only after the ice melts. Frozen pipe repair in winter on this housing usually means an exterior-wall or attic run that was never insulated for a hard freeze. After the pipe holds, we look at hose bibs and the water heater drain because those are the next spots that split.
Do Lavon houses on Bear Creek lines see the same yard leaks?
Lavon sits in Collin County too, but Bear Creek Special Utility District sells the water, not the City of Wylie. The clay is still Houston Black in character, and the housing is mostly new slab streets along SH 78, so the buried run is PEX more often than galvanized. Yard leaks there still show as a meter that turns with everything off and as a soft strip between the meter and the slab. We treat that town as its own utility and its own pipe era, not as a copy of a Wylie downtown cottage.
Why would a new Josephine water line still leak in the yard?
Josephine straddles Collin and Hunt counties, and most of the new streets were built in a short boom on slab. New PEX can still leak at a bad crimp, a scraped bury, or a fitting that was left under tension when the trench was backfilled in clay. The City of Josephine sells the water, so meter location and bury depth can differ from a Wylie city tap. We pressure-test the run and inspect the fittings before we blame the pipe material. A same-day diagnosis on that street is a set of readings, not a guess from the age of the house.
Can you work a Caddo Mills house in Hunt County after dark?
Caddo Mills is in Hunt County, and the City of Caddo Mills bills most in-town taps. We still run the same meter-to-hose-bib pressure checks on FM 36 and SH 66 streets because the clay and the slab construction do not stop at the Collin line. After-hours work follows the same test order: isolate, measure, then open only what the numbers justify. Older Main Street houses may still have galvanized, while the new subdivisions are PEX, so we confirm the material before we cut.
Why does a kitchen sink drain keep backing up after it was cleared?
A kitchen sink drain that keeps backing up usually means the stop is past the trap, in the branch or the yard lateral, not in the basket strainer. Food waste and grease coat PVC the same way they coated older cast iron, and a belly in the line will refill as soon as the cable is pulled. We run water at the sink and at an upstream tub to see whether the blockage is local or shared. Camera work on the line tells us whether drain cleaning for a clogged kitchen sink needs a cut-out or just a thorough cable.
When is appliance fuel line work part of a plumbing visit?
When a range, dryer, or log set is in the same visit as a water-line repair, we treat the appliance connector as its own test. We check shutoff position, soap the joints, and verify the connector type matches the appliance. That is not a substitute for the gas company on a smell or a leak in the yard main. If you smell gas or suspect a gas leak, go outside immediately and call 911. This is a serious emergency that needs urgent attention from the gas company.
Wylie Pipe Pros is the plumbing company that starts at the Collin County meter and works inward through the slab, the heater, the drains, and the fixtures. Houses, townhomes, and condos in Wylie get that full path, and so do the towns we named. Plumbing repair on this crew is a set of readings, then a repair that matches the pipe and the clay. If the house is in 75098 or on one of those nearby streets, the visit is the same order every time.
We stay on the water line first because that is what fails on this soil, and we still cover the equipment it feeds. Reach out when the meter moves, the slab is wet, or a tap will not recover. The gauges come off the truck, the numbers get said out loud, and the house gets put back together.
Reach out to us for assistance.
ZIPs we cover: 75098, 75166, 75173, 75135
Area We Are Servicing
Address: 101 Kristen Ct, Wylie, TX 75098
Taking care of your home or business includes taking care of your plumbing. Simple steps like not pouring grease down the sink and knowing where your emergency water shut off valve is can make a big difference. However, when professional help is needed, it is important to call a team that knows what they are doing.
We are dedicated to maintaining the health and safety of the plumbing systems in Wylie. We take pride in our work and in our community. Thank you for considering Wylie Pipe Pros for your plumbing needs at home or work. We look forward to serving you.